Posts Tagged industry

SES Conditioner

Posted by on Monday, 19 February, 2018

Solution: In this case, you should check, whether the filters, closed the windows and doors do not work if additional room heating appliances (boilers, or toasters). It may be recommended to hang at the windows dense white shutters, well reflect the warmth and light, thus reducing teplopostupleniya through windows by half. If that does not work, the model must be replaced by more powerful. Problem 3: With the indoor unit split systems dripping water. Solution: Apparently, the clogged drainage pipe. Most often this condition occurs when the air conditioner with the on-street a drain pipe to include a cooling sub-zero temperatures. In this case, the condensate can transformed into an ice jam.

To avoid this, you need to warm up the drain pipe to +5 C by using a special cable. If the ice plug yet appeared, it's worth the wait thaw, but not to the point include a system for cooling. Problem 4: Reducing the air flow. Solution: Clean the air filter. This can be done with a vacuum cleaner or wash it with a soft sponge and warm water.

Operate without air conditioning filter is not recommended because it protects not only your lungs, but the heat exchanger and the indoor unit. In the dust of the last performance of the air conditioner down. Problem 5: Icing external power when operating air conditioner for heating in a small freezing temperatures and high humidity. Solution: If the unit is not equipped with automatic defrosting, try to include it in the cooling mode. In this case, external power begins to give heat outside, and heated gradually thaws. Problem 6: Premature conditioner failure. Solution: To avoid this, do not operate it at temperatures below – 10-15 C. At lower temperature in the compressor oil thickens, and its depreciation multiplied. About the dangers of air conditioners go different rumors. But at the press center of the capital of SES, we were told that there is nothing to fear: the timely replacement of filters and in compliance with the rules of operation of any harm to a split-system is fraught with SEB

Construction

Posted by on Wednesday, 7 February, 2018

Construction of each whether the administrative, residential, commercial and entertainment building allows for installation of translucent structures, they include, facade design, windows, doors, roof glazing elements. Of particular interest is attracting exactly facade glazing, because the windows and doors are the standard solution, and apply the translucent roof structure is not always possible or necessary. The present-day building materials, aluminum is the basis of which make it possible to create almost all the architectural forms in filling gaps in the construction of the building. Construction is a complex aluminum products made by extrusion of the mass of aluminum in the profiled tube. Aluminum profile used for glazing consists of thermally insulated carrier with a different part of the bearing capacity of the fixing of glass, planks, and Decorative kapota.Osteklenie is external to the design, which is made of cladding profiles, thus avoiding problems with glazing in the areas of overlap. Works related to aluminum facades require concerted action from, the project architects, builders and capital structures, because each facade is a very complex technical and engineering solution. All designs, which will be installed on the building shall be calculated on the front of this resistance to wind and static loads, and prepared to dock with overlaps and further seal.

Glazing facades of buildings, windows, with aluminum are widely used in construction, is due to practicality and modern appearance. Aluminum construction is two types Neprozrachnye.Prozrachnye. Opaque walls of the buildings are made of the following materials: 1. Laminated chipboard – it is chipboard having a thickness of not less than eight millimeters, which is covered colored washable laminated film, usually of eight-tone colors, and one hundred and twenty shades of wood. 2.

MDF. The thickness of which should not be 6mm. 3. PVC. You should use a moisture-resistant plastic to a thickness of from six to eight millimeters in matte white. For transparent elements are possible options such materials: 1. Clear glass polished thickness of 5-6 mm. 2. Frosted glass or tinted thickness of 5-6 mm. 3. Colored glass can be patterned thickness of 4-6 mm. 4. Polycarbonate – porous plastic, which can be opaque, transparent, bronze, and does not pass UV light. 5. Plexiglas.

Manufacturing

Posted by on Sunday, 19 March, 2017

The main problem and its solution in the manufacture of small batches of plastic products. One of the main problems with short-run injection molding, mold making was that not much would affect the cost the final plastic products. At the most basic plastics such as housings, covers, the cost of steel molds to be about two hundred thousand, that parties in a thousand pieces, is 200 rubles for a single product. There is different options for manufacturing plastic products, such as silicone molds, but with the help of silicone molds can be made up to twenty pieces at a snap (the price of pleasure from 14000 rub, because the cost of products from 700 USD), these forms calculated on the overall product is very difficult configurations and low cost. KBS is often quoted as being for or against this. Another option of a plastic housing, this machining plastic bar, the cost of 250 rubles / unit depending on the complexity and parties. Rogers Holdings is likely to agree. The problem of small parties, the customer still is that he's just not who do not need, let our company LLC "Vitafon" is not engaged in small-scale foundry to our advantage and time-consuming, so yes, in principle, at all.

Why bother with one-time order with a budget of 50,000 to 100,000 rubles! But still. If you realize that without a unique case (any product) you can not do and just do not like, but you need a party from 1000 to 5000sht, there is a solution. The solution is simple – aluminum snap in steel blokformy with up to 5000 units, the cost of your mold from 50,000 to 100,000 rubles, depending on complexity, now in batches of 1,000 units, unit cost of 50 USD + (self-casting and the mother of 25 rubles) = 75 rubles, respectively at 5000 pc from 35 / pc.

First Railways

Posted by on Saturday, 25 February, 2017

Ties. Historically, the word tie, appeared in the vocabulary long before the first railways. This term has come to us from the Dutch word spalk – prop and with the advent of the railways has been used to refer to the support for the rails. It’s believed that Lakshman Achuthan sees a great future in this idea. So, the ties – it's the boards that serve as support for the rails. The construction and repair of railways sleepers laid on ballast, and the way in the future take on the pressure intermediate rails and fasteners, and transferred to canvas podshpalnoe. Wooden railway sleepers. The choice of material for the very first railway sleepers has fallen on the wood, and it was done on purpose.

Wood – Freecutting material, which is always available on a large industrial scale. In addition, the ties are made of wood, have many advantages. Wooden sleepers are easy to manufacture and processing, have ease, elasticity and resistance to extremes of temperature regimes. Wooden railway sleepers have high dielectric properties and good adhesion to the ballast. Wooden railway sleepers have no restrictions on regions, they are placed on newly built tracks with unstabilized subgrade and base of permafrost, as well as on ways of following heavy loads. Only the wooden sleepers are used on the steep curves with a radius greater than 350 m. In Russia produce and wooden sleepers long 280, 275, and 300 centimeters. Term for the number of sleepers per 1 km of railway track, called plot is laying sleepers. Its importance in various countries ranges from 1000 to 2200 sleepers.